MATERIAL SAFETY DATA SHEET
Discontinued:
Date of Preparation: 01/24/2007
Page 1of 7
SECTION I - Product and Company Description

Product Name: Adhesive 5 Minute Epoxy (Part A)
Product Use: Resin Compound
Product Number: 11-676148-000A

Company: Brunswick
525 W. Laketon
Muskegon, MI 49443

Telephone #: 1/231/725-4972
Emergency #: 1/800/255-3924
CHEMTEL #: 1/800/255-3924
International CHEMTEL #: 1/813/248-0585

SECTION II - Composition/Information on Ingredients
HAZARDOUS
INGREDIENT
MATERIAL DESCRIPTION
REF#		CAS#ECN#SARA
313
Y/N
% Wt.
Siloxanes & Silcones
Glycidoxypropyltrimethoxysilane
Titanium Dioxide		67762-90-7
2530-83-8
13463-67-7		N 5.0
Y 2.0
Y 1.0
NONHAZARDOUS
INGREDIENT
MATERIAL DESCRIPTION
REF#		CAS#ECN#SARA
313
Y/N
% Wt.
Reaction product of Bisphenol A and Epichlorohydrin
Alkyl Glycidyl Ether		25085-99-8
68609-97-2		N 83.0
N 9.0

This product contains a chemical reported to be a carcinogen or suspected carcinogen.
SECTION III - Hazards Identification


11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 2 of 7
SECTION IV - First Aid Measures

EYE CONTACT: Flush with lukewarm water for 15 minutes. Contact physician.
SKIN CONTACT: Do not remove with solvent. Use waterless hand cleaner followed by soap and water. Remove and clean contaminated clothing.
INHALATION: Remove exposed individual to fresh air. Restore breathing, if necessary. Get medical attention.
INGESTION: Rinse mouth. Call a physician or Poison Control Center immediately. DO NOT induce vomiting unless advised by a physician.
SECTION V - Fire-Fighting Measures

EXTINGUISHING MEDIA: Use CO2, Dry Chemical or Foam

Firefighters should be equipped with self contained breathing aparatus and turnout gear.
Vapors caused by heating of this product may develop a flammable atomospere in confined or poorly ventilated areas.
SPECIAL RISKS: Vapors heavier than air. Development of hazardous combustion gases or vapors possible in the event of fire.
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE FIGHTING: Fire Fighters should use self-contained breathing apparatus with face piece.
OTHER INFORMATION: Keep away from sources of ignition. Prevent fire-fighting water from entering surface water or groundwater. Cool Container with spray water from a safe distance. Never use welding or cutting torch on or near container (even empty) because product may ignite explosively.
SECTION VI - Accidental Release Measures

PERSON RELATED PRECAUTIONARY MEASURES: Avoid substance contact. Do not inhale vapors. Ensure fresh air supply in enclosed areas.
ENVIRONMENTAL PROTECTION MEASSURES: Do not allow to enter sewage system, surface or groundwater.
PROCEDURES FOR CLEANING/ABSOPRTION: Use inert absorbent material to take up spilled material. Place in appropriate container until proper disposal method is determined.
SECTION VII - Handling And Storage

NOTES FOR PREVENTION OF FIRE AND EXPLOSION: Keep away from sources of ignition. Use and store this product with adequate ventilation.
NOTES FOR SAFE HANDLING: Avoid generation of vapors. Do not inhale vapors.
STORAGE: Store in well-ventilated area between 40 F (4C) and 100 F (38C). Store away from heat and sources of ignition.
Brunswick takes no responsibility for determining what measures are required for personal protection in any specific application. The general information given should be used with discretion.


11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 3 of 7
SECTION VIII - Exposure Controls/Personal Protection

Hazardous
Component		ACGIH
TLV(TWA)
PPM		OSHA
PEL
PPM
Siloxanes & Silcones
Glycidoxypropyltrimethoxysilane
Titanium Dioxide		5 mg / m3
250 ppm
Not established		20 mppcf
200 ppm
Not established
NonHazardous
Component		ACGIH
TLV(TWA)
PPM		OSHA
PEL
PPM
Reaction product of Bisphenol A and Epichlorohydrin
Alkyl Glycidyl Ether		Not established
Not established		Not established
Not established

PERSONAL PROTECTIVE EQUIPMENT: Protective clothing should be selected specifically for the working place, depending on concentration and quantity of the substances being handled. The resistance of the protective clothing should be ascertained from the respective supplier.

RESPIRATORY PROTECTION: Required when vapors are generated.

EYE PROTECTION: Splash goggles.

HAND PROTECTION: Chemical resistant gloves and skin cream.

INDUSTRIAL HYGIENE: Immediately change any contaminated clothing. Apply skin protective barrier cream. Wash hands and face after handling product. Do not inhale vapors.
SECTION IX - Physical and Chemical Properties

Physical State: Thick creamy liquid
Odor: Slight oil odor
pH: Esentially neutral
Viscosity:
Lowest Flashpoint: 350 ° F (176 C).
Explosion Level: Lower - Not determined Upper - Not determined
Vapor Pressure: <0.06 mm Hg @70 F (21 C)
Vapor Density: (Air = 1) Not determined
Weight Per Gallon: 9.15 lbs./gal.
Solubility: Nil in water


11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 4 of 7
SECTION X - Stability and Reactivity

Conditions to be avoided: Exposure to flame or intense heat. Poor ventilation.
Substances to be avoided: None known.
Hazardous decomposition products: Phenolic CO and CO2
Further information: Hazardous polymerization will not occur under normal conditions. When mixed in amounts greater than 1 pound (454 grams) with aliphatic amines, irreversible polymerization will take place with considerable heat build up.
SECTION XI - Toxicological Information

Acute Toxicity:
Rat Oral LD50 - >2000 mg / kg

Specific symptoms in animal studies:
Subacute to chronic toxicity:
Bacterial mutagenicity:
Further toxicological information:

Further Data: Rabbit eye irritation - slight to moderate
Rabbit skin irritation - slight



11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 5 of 7
SECTION XII - Ecological Information

Biologic degradation: No data

Ecotoxic effects: No data
Biological effects: No data
Fish toxicity: No data
Daphnia toxicity: No data
Maximum permissible toxic concentration: No data
Algeal toxicity: No data
Bacterial toxicity: No data
Protozoa: No data
Further ecological data: No data
SECTION XIII - Disposal Considerations

Product: Chemicals must be disposed of in accordance with national and local regulations.

Packaging: Packaging must be disposed of in compliance with national and local regulations.


11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 6 of 7
SECTION XIV - Transportation Information

Package Desc:
Weight:
Dimensions:
Freeze/Thaw stable:
Flashpoint: 350 ° F (176 C).

Land transport:
Classification: Not Regulated
Name:

Transport by sea:
Classification: Not Regulated
EMS
MFAG
Name

Transport by air:
Classification: Not Regulated
Name:
Packaging Instructions:

The transport regulations are cited according to international regulations and in the form applicable in the United States. Possible deviations in other counties are not considered.
THIS TRANSPORT DATA APPLIES TO THE ENTIRE PACKAGE.
SECTION XV - Regulatory Information

Labeling according to Land Transport:
Hazard:
Package:
Other: ORIENTATION ARROWS

Labeling according to Sea Transport:
Hazard:
Package:
Other: ORIENTATION ARROWS

Labeling according to Air Transport
Hazard:
Package:
Other: ORIENTATION ARROWS


11-676148-000A
Adhesive 5 Minute Epoxy (Part A)
MATERIAL SAFETY DATA SHEET
Page 7 of 7
SECTION XVI - Other Information



The information contained herein is information received from our raw material suppliers and other sources and is believed to be reliable. This data is not to be taken as warranty or representation for which Brunswick assumes legal responsibility.

This Safety Data Sheet complies with EC Commission Directive 2001/58/EC of July 2001